Thursday, September 27, 2007

Part 5, Lowe's Tool Case Wristwatch Conversion

Cutting the Foam Padding


Not a lot of s this time. Wasn't that much to photograph when it's replicating a few tasks numerous times.The test of "Plan A" to glue the foam padding to the divider didn't work. The adhesive works great on the foam. Doesn't adhere worth a tinker's dam to Plexiglas. Moved on to "Plan B" this evening with the same small divider, the same piece of foam (which was very salvagable) and tried some Duro spray contact adhesive. Spray a coating onto the foam and Plexiglas, wait about a minute or so, and then press them together. WOW! That works! Immediately!! Better have it positioned just right; there's only one shot at it and no sliding things around to reposition them. Won't have to wait overnight to know if this works or not. Doing the "Proof of Concept" test piece last night, which disproved the concept, paid off in not wasting a lot of time redoing ten larger dividers. This is the small divider with the foam attached to it using the spray contact adhesive:

Now that the method to attach the foam to the dividers is settled, the other pieces of foam have to be cut. A small square, larger combination square and long steel rule are used to mark the pieces of foam. A little planning with the dimensions required beforehand maximizes use of the width of the sheet of foam and minimizes scrap. Most of the scrap can be used later to make pieces to fit around the case sides and in the pocket bottoms. No foam has been pitched yet! Here's the layout marked for three 5 inch long dividers using a fine point Sharpie:
Ten pieces in three different lengths are needed to cover all the Plexiglas dividers (not counting the tiny one which is already covered). The line across the center marks where the foam will go across the top of the divider. Found this helped immensely when positioning the Plexiglas after applying the adhesive for the first side, and then pulling the foam across the top to attach it to the other side after the second application of adhesive. The short, tiny piece was easy. The longer ones may be a little trickier.
I had set up a small table outside in my covered porch on which to do the spray adhesive. Put sheets of packing paper down (essentially newsprint paper without any newsprint on it). It was so humid tonight that the paper had become quite damp. Too humid to work with the adhesive. Attaching the foam to the Plexiglas will have to wait until tomorrow night. After that, I'll use the small piece that's already done and do another "Proof of Concept" in covering it with Ultra-Suede.

Part 4: Lowe's Tool Case Wristwatch Conversion

Padding the Dividers

Link to Part 3: Creating the Grid

Not much to show this evening. Sometimes it pays to do a "Proof of Concept" to verify that something will work well, before replicating it many times. Limits the effort expended in a "Do-Over" and wasted materials. That's what I did tonight.

1/2" foam needs to be glued around each of the Plexiglas dividers. I've never used this combination of foam, Plexiglas and adhesive before. The smallest divider is the very short one in front dividing the narrow accessory pocket in two. It's real purpose is structural, to keep a long divider that came with the case pressed up against four longer Plexiglas dividers on the other side of it. If it were to bow too much away from them, and it is somewhat flexible (more so than the Plexiglas), the dividers could slip out of the slots. It's small enough that I can work with it easily, and if I need to strip off the foam and start over with Plan "B" (a different adhesive), I won't have wasted much adhesive or foam.

I cut a 6" long by 1-1/2" wide piece of foam to wrap around the top and sides of this divider. Cutting it the same width as the divider allows wrapping it around a little more precisely and I can trim off some to expose enough Plexiglas - about 1/8" - to fit the case slots (around the inside edge and on the dividers it came with) after the adhesive sets.







Then I put some adhesive on one half of it and pressed the Plexiglas divider onto that side.














After that I put some adhesive on the other half, wrapped it around and used a small scrap block of wood to hold it down.








I'll know in the morning if the adhesive will work well enough to hold the foam firmly to the Plexiglas. If not, I have Plan "B" and a Plan "C" which are two different adhesives that are supposed to work on many different materials, including foam.


Now that the concept was demonstrated with one piece of foam, the next step was cutting out all the pieces of foam to cover all of the dividers.

Monday, September 17, 2007

Review: UTS München 3000M PVD

UTS München 3000M PVD:
The Ultimate Diver?

Summary:
  • Only 200 made; all by hand
  • Stainless steel Case and band (PVD optional)
  • 43mm diameter
  • 16mm thick
  • Solid link stainless steel band
  • Band attaches to case using unique screw system (no springbars)
  • 220 grams
  • 3,000 meter depth rating
  • ETA chronometer grade 2824-2 (adj. 5 pos.)
  • Solid stainless steel case, crowns and back
  • Sapphire crystal; 5mm thick with AR coating
  • PVD coating on case and band are optional
I’m not that big into divers. I own only one that I would consider a true diver, a Tissot Seastar 1000. It's one my modest budget can afford. This is a review about a diver I've seen and done some research about to find out more about it and the company behind it. It's unique and interesting enough I want to share with you what I discovered.

Divers come in all manner of styles across all price points from nearly every watch maker. Not all are true divers though. They have the appearance of a diver’s tool watch, but are missing the necessary depth rating; they’re “desk divers.” A diving watch today is not as critical anymore for serious deep and commercial divers as it once was because it’s not the primary timing device. Today these divers use small dive computers as they’re more efficient with the dive plan. The modern dive computer strapped to a diver’s body can calculate safe ascent times using more complex algorithms than one can do with simple hand computations or mental calculations that result in estimates padded to keep any error in the direction of diver safety.

However, the dive watch on their wrist is a backup to the dive computer. Since I wanted to know more about true divers' tool watches, ones that could be used by deep or commercial divers as their dive computer backup, I set about looking for the ultimate deep dive tool watch. After several hours doing Google searches using of all manner of search words and phrases, I came across a company that one doesn’t hear of much in the general watch collectors' community. Perhaps it's better known in forums that specialize in dive watches, or in deep and commercial diving itself, but it's not heard of much, if at all on the general watch collector forums I regularly visit.

The company is UTS München. It's a very young and small German firm founded in 1991. They specialize in making very serious dive watches that are assembled by hand, and thoroughly tested and certified before it goes out the door. These are real tool watches rated for very deep diving. Among their collection, one stands out from the rest as their current flagship, the UTS München 3000M Professional Diver. It’s called the 3000M because it’s rated to 3000 meters – yes – that’s right – 3000 meters of static depth pressure, not feet. The 43mm diameter and 16mm thick case is made of surgical stainless steel with 3-1/2 mm thick walls and a 5mm thick sapphire crystal. It’s so sturdy and rugged that it can withstand its incredible depth rating without needing a helium valve. Any watch this beefy will have some mass: 220 grams worth.

The second crown one might assume is the valve when looking at photos of them? That’s a timing bezel lockdown to keep it from accidentally being rotated while in use. Their engineering gave thought to error-proofing a critical feature that could have dire consequences if it's accidentally rotated from its set position. It's a feature not found on most dive watches!

It also comes with a massive, solid stainless steel band with special screw attachments to the case. No way this one's going to come off accidentally due to a worn or weak springbar if it's accidentally bumped or snagged on something during the dive. This particular variant has been PVD coated black, an extremely hardy finish (others come in the natural stainless steel with a brush finish).

There was no skimping on the movement inside either. It’s a chronometer grade ETA 2824-2 adjusted to 5 positions. It's the most expensive grade with greatest attention to detail one can get from ETA to put into a watch. Adjusting a movement is no small matter, and doing so to five positions (orientations of the movement) can be quite time consuming!

Their price new is too salty for me to afford for now; it's over $3,000. Even so, it's less expensive new than a Rolex Sea Dweller, the Rolex flagship of deep divers, which has less than half this one's depth rating. I'll have to settle for just being able to look at them and drool uncontrollably (fortunately they can easily withstand being drooled on). If I ever do have that kind of money for a watch, the trouble may be finding one. All of their watches are made made in very limited numbers; only 200 of each model. I did find a couple used ones that were advertised and sold on watch forums within the past year. They were the PVD coated versions, and both were in excellent condition with asking prices in the upper half of the $2000-$3000 range. Someday, maybe, after I win the Lotto, I'll be able to find and buy one. Until then I'll have to dream of one on my wrist. [sigh]
Summary:
  • Only 200 made; all by hand
  • Stainless steel Case and band (PVD optional)
  • 43mm diameter
  • 16mm thick
  • Solid link stainless steel band
  • Band attaches to case using unique screw system (no springbars)
  • 220 grams
  • 3,000 meter depth rating
  • ETA chronometer grade 2824-2 (adj. 5 pos.)
  • Solid stainless steel case, crowns and back
  • Sapphire crystal; 5mm thick with AR coating
  • PVD coating on case and band are optional
Current MSRP is over $3,000, but they can sometimes be found used in excellent condition for a few hundred dollars less than that. Takes some patience waiting for one; there are only 200 of them and owners don't part with them often.

Note: I do not have any association with UTS München, or their dealers or distributors.

Sunday, September 16, 2007

Review: Rado Original DiaStar XL Automatic

Rado Original DiaStar XL Automatic

Summary:
  • Updated version of the original 1962 "Scratch-Proof" watch
  • 39 mm wide (across the 3 and 9)
  • 46 mm long (across the 12 and 6)
  • 11 mm thick
  • 20mm wide X 3mm thick solid link stainless steel band
  • 180 grams
  • ETA 2836-2 25 jewel 28,800 bph auto movement
  • Titanium carbide outer case
  • Stainless steel inner case, crown and back
  • Sapphire faceted crystal
  • Signed outer case, crown and band clasp
  • Rotating anchor logo on dial
  • Lume stripes on hands and subtly embedded in indices
Rado was founded in 1917 as the Schlup & Co. in Lengnau, Switzerland. They began by producing only watch movements. Longines merged with them in 1931 to form ASUAG, and they became Switzerland's largest movement maker. In 1983, ASUAG with its Rado and Longines brands merged with SSIH, which held the Omega and Tissot brands, to form the ASUAG-SSIH Holding Company. In 1986 it was renamed SMH, and was renamed again in 1998 as The Swatch Group. Within The Swatch Group, Rado and Longines are considered "High Range" brands, between "Prestige Range" brands such as Blancpain and Omega, and "Middle Range" brands such as Tissot and Mido.

The Rado DiaStar Original made its debut in 1962 as the world's first "scratch-proof" watch. Since then, Rado has distinctively differentiated itself from the rest of the watch industry by using unique and unusual high technology materials for equally unique and "scratch-proof" dress watch designs. The Rado Original DiaStar and its sister collection, the Original, continue the general case, dial and crystal design of the 1962 DiaStar Original, making it their classic.

While details have changed over the years, the general concept has remained true in design concept as well as appearance. The Original DiaStar comes in four sizes:
  • Small; women's size (21 x 25 mm quartz)
  • Medium; womens' size (27 x 30 mm automatic)
  • Large; a men's mid-size (35 x 42 mm)
  • Extra-Large; a men's large size (39 x 46 mm)
The one depicted here is the "XL" or Extra-Large, a size that's difficult to find. The vast majority of the men's found are the "Large" size. Difference between the two sizes is essntially that, their size. The "scratch-proof" hard-metal case shell is made of titanium or tungsten carbide, molded under extremely high heat and pressure, and polished to a mirror finish. The shell is permanently fitted over a traditional 316L stainless inner casing to house the movement, is signed with the Rado name on the side opposite the crown, and has the watch's serial number finely etched into the side below the "6" instead of the traditional location on the back.

The crystal is of thick, multi-faceted man-made sapphire (aka corundum), harder and more "scratch-proof" than the case shell. The faceting is subtle; normally when looking at the watch one sees vertical bands on the dial that at a glance appear to be part of the dial finish itself. In reality, it's the subtle facets and how they cast light on the dial, which has a subtle, very fine metallic flake finish. While the location of the logos, day/date and and trademark rotating anchor have changed, the general dial and hands style hasn't changed in at least 30 years.

Most of the vintage seen on the market have bands that were made by "NSA" for Rado. This is not the National Security Agency, but a Swiss company that made stainless steel bands for not only Rado, but quite a few other high end watch companies. These were unique bands that had a traditional folding clasp with a unique feature that would allow it to stretch some using internal springs and a metal tab. Links were of heavy stainless steel sheet metal rolled around thick pins. They were high quality bands in their era. Unfortunately, NSA is no longer in business. These have been replaced on at least the "XL" size with a band that looks similar but is noticeably thicker and heavier with solid stainless steel links that are highly polished to a mirror finish. The clasp is a unique butterfly with one side of the butterfly shorter than the other. The signed closure has side buttons to open it, and the thick butterfly mechanism under it is made of Titanium (the only titanium part of the watch).

The signed crown is partially recessed into the case to reduce its prominence, but can still be wound without undue difficulty. The faceted sapphire crystal is relatively thick compared to a flat one, but the thin vertical facets are subtle giving a shallow rise from the sides toward a wider flat portion in the middle. Unlike prominently faceted crystals that are more like prisms, the dial is read easily through this one under all lighting conditions. The dial has the trademark rotating anchor just below the 12, which is slightly weighted and pivots as the watch is turned. The applied "Rado" and "DiaStar" logos provide horizontal visual balance at the 9 and 3 positions; the anchor is visually balanced vertically by the 6-eater day/date window. This gives a horizontal and vertical symmetry. Indices are medium width applied batons that stand proud from the dial along with all the logos. These provide good visibility for reading time without clutter or distracting from the logos or day/date, and there is visual dimension and depth. Many dress watches do not have any lume on the dial or hands, and this is a "deal breaker" for some that like the rest of the design. Not so with the DiaStar. Rado put thin stripes of lume down the centers of the hour and minute hands, and down the centers of the hour indices. One might not notice the hour marker lume as it's subtle. At first glance it can appear that it's simply a groove down the middle and part of the design, until it gets dark and one sees the nice lume.

Prior to formation of The Swatch Group, Rado used A.Schild movements, which were considered excellent workhorses, and were used by numerous mid-range and high-range watch brands. A number of movement manufacturers, including A.Schild, were consolidated into ETA, another very excellent movement maker, when The Swatch group was formed. ETA makes the movements for current Rados. The movement inside the Men's Original DiaStar is a 28,800 bph, 25 jewel ETA 2836-2 day/date automatic. This is a classic, exceptionally reliable workhorse that comes in several grades. The grade used by Rado is the second highest, an elaboree just below the extremely expensive "Chronometer" grade that have COSC certification and are intended for certified chronometers. Instead of the traditional 3-eater horizontal day/date, the day abbreviation is displayed vertically.

Fit, finish and workmanship is impeccable, which is to be expected of a "High Range" watch. It's a classic design dating to the early 1960's that carries Rado's heritage of unique designs using unique materials that can withstand normal use and still look brand new 10, 20 and even 30 years later. The "scratch-proof-ness" and durability of the high-tech materials Rado uses is across all its collections, not just the Original DiaStar, is unrivaled in the industry.

Summary:
  • Updated version of the original 1962 "Scratch-Proof" watch
  • 39 mm wide (across the 3 and 9)
  • 46 mm long (across the 12 and 6)
  • 11 mm thick
  • 20mm wide X 3mm thick solid link stainless steel band
  • 180 grams
  • ETA 2836-2 25 jewel 28,800 bph auto movement
  • Titanium carbide outer case
  • Stainless steel inner case, crown and back
  • Sapphire faceted crystal
  • Signed outer case, crown and band clasp
  • Rotating anchor logo on dial
  • Lume stripes on hands and subtly embedded in indices
MSRP for the Original DiaStar XL Automatic is currently $695. They can be found with discounted prices, sometimes significantly discounted in spite of Rado's efforts to eliminate discounting, but due to their relative rarity compared to its Large sized smaller brother, it requires significant searching and patience.

Note: I do not have any association with The Swatch Group, Rado or their dealers other than having bought a Rado from an authorized dealer.

Saturday, September 15, 2007

Review: Fortis Flieger Chronograph Automatic

Fortis Flieger Chronograph Automatic


Summary:
  • 2004 European Aviation Watch of the Year
  • 40 mm diameter
  • 14 mm thick
  • ETA 7750 chronograph movement
  • Stainless steel case, crown, pushers and back
  • Sapphire crystal
  • Signed crown
  • Solid link stainless steel band
  • Flip-lock clasp
  • Central "stop" seconds hand
  • 30 minute accumulator
  • 12 hour accumulator
  • Day/date complication
  • Standard seconds hand sub-dial
  • 100 meter depth rating
I’m not that big into chronographs as I only own one. It's not this one, but I eventually hope to have a Fortis Flieger Chronograph in my own collection. Nearly all current aeronautical watches include a chronograph complication and this particular Fortis is a unique example of one.

Fortis' entire market focus and brand identity is exclusively with modern aeronautical watches, but they didn't start out solely serving that market segment as they do today. A Swiss company founded in 1912 by Walter Vogt, it set up production in 1924 with John Harwood, inventor of the automatic wristwatch, and released their first auto-winding watch in 1926. Over the years that followed, they made various types of watches including their first chronograph in 1937. Various alarm watches were introduced in the 1950’s after WWII that culminated in their Brain Matic Auto Alarm during the early 1970's.

In 1987, 75 years after the company's founding, Fortis took a direction that would ultimately change its long-term brand identity with the introduction of their Flieger collection of aviation watches. During the two decades that have followed, aeronautical and astronautical watches have become their entire focus. It has paid off for them handsomely. Fortis has been the exclusive supplier of wristwatches for manned space missions to Russian Federal Space Administration Cosmonauts since 1994. They enjoy a relationship today with the Russian Federal Space Administration that parallels the long-term relationship Omega has had with NASA. Fortis’ chronographs use the venerated ETA 7750 chronograph movement, originally designed and made by Valjoux.

Why this Fortis chronograph is special:
Some of the chronographs in their various watch lines are quite pricey. I found the Flieger collection "street prices" more affordable while having similar characteristics of their other collections. The "flagship" of the Flieger line stood out from the rest in the collection, the 40mm diameter, 14mm tall Flieger Chronograph Automatic. It's powered by an ETA 7750 in a solid stainless steel case with sapphire crystal, and a solid link stainless steel band. The chronograph is big enough with it's narrow bezel to have a nice, large dial for readability, and yet it's physically small enough not to be bulky or feel cumbersome when wearing it while flying a plane -- striking a balance between size and utility. If a pilot is that unfortunate enough to end up "in the drink" it is blessed with a 100 meter depth rating, sufficient for swimming. The Flieger Chronograph was received so well by the civil and military aviation that it received the 2004 European Aviation Watch of the Year Award. It embodies Fortis' significant strategic shift in 1987 to focusing solely on modern aviation timepieces with the introduction of the Flieger line, and it's the model within the line that has received recognition from the aviation industry for its concept and design. One couldn't ask for much more than one of their more affordable chronographs representing so much about the Fortis brand and two decades devoted to producing aviation watches.

I started out by stating I'm not that big into chronographs. Having looked at many others, this is one I can see myself saving for -- and not buying any watches for some time to accomplish it. Its street price is more affordable than many in its class, it reflects a major direction change in Fortis' history, and it carries the prestige of a significant aviation industry award.

Summary:
  • 2004 European Aviation Watch of the Year
  • 40 mm diameter
  • 14 mm thick
  • ETA 7750 chronograph movement
  • Stainless steel case, crown, pushers and back
  • Sapphire crystal
  • Signed crown
  • Solid link stainless steel band
  • Flip-lock clasp
  • Central "stop" seconds hand
  • 30 minute accumulator
  • 12 hour accumulator
  • Day/date complication
  • Standard seconds hand sub-dial
  • 100 meter depth rating
Current MSRP with the "Oyster" style stainless steel band is $1750, but with some searching it can be found substantially discounted.

Note: I have no affiliation or association with Fortis, or any of their dealers or distributors.

Friday, September 14, 2007

Review: Zodiac Astrographic 2000

Zodiac Astrographic 2000 Summary:
  • Updated version of the original 1971 Astrographic SST
  • No more than 500 in each style made during 1999, and marketed during 2000-2001
  • 38 mm diameter
  • 12 mm thick
  • 20 mm wide X 3mm thick solid stainless steel band
  • 180 grams
  • 200 meter depth rating
  • ETA 2824-2 25 jewel, 28,800 bph auto movement
  • Solid stainless steel case, crown and back
  • Sapphire crystal
  • Signed back, crown, and pushbutton butterfly clasp
  • Unique orbiting satellite hour/minute and red moon seconds hands "mystery dial"
Zodiac was founded by Ariste Calame in Le Locle, Switzerland, in 1882, a center of Swiss clock and watch making for centuries, as "Ariste Calame." The Calame family had lived in the region since at least the 16th Century. While the "Zodiac" name had been used for some time, it wasn't registered until 1908 by Ariste's son, Louis Ariste Calame. The company went through a succession of registered names in the years that followed, becoming "Ariste Calame: Montres Zodiac" in 1923, and eventually became just "Zodiac, S.A." The Astrographic SST (Split-Second Timing) made its debut in December 1971, with the same uniquely original concept found in the Astrographic 2000: orbiting satellite hour and minute hands with a "fiery red moon" seconds hand "mystery dial." Although case and band styles changed during the 1970's, the watch maintained the same concept for its "mystery dial" hands. I've never been able to determine exactly when the original Astrographic collection was discontinued, but it had disappeared by some time in the 1980's. Willie Gad Monnier, formerly a Tag Heuer principal, purchased Zodiac in 1990 while it was suffering financial troubles and modernized its collections with a noticeable Tag Heuer influence. In 1997, the company declared bankruptcy. Not quite a year later in 1998, Genender International, Inc. acquires the brand and all its surviving inventory. It's under their ownership that nearly all of Zodiac's mechanical watches are discontinued and replaced with new quartz collections. Only the Super Sea Wolf and Marine Life models survived with mechanical movements. In October 2000, Zodiac announced the resurrection of the Astrographic which had been one of their most popular and best known collections. The new, high end Astrographic 2000 was designed with updated materials befitting its intended market segment, a sleek look that maintained historical elements of its case styles and the mystery dial, and an MSRP of $1295. The Astrographic 2000 only lasted 13 months though. In October 2001, Fossil purchased Zodiac from Genender. A month later Fossil announced discontinuation of Zodiac's collections, including the Astrographic 2000, and relaunched completely new lines of watches under the Zodiac name, showing them in the April 2002 Basel Watch Show with retail deliveries later in the Fall. The Astrographic 2000 (along with the Super Sea Wolf) became instant collectibles due to their popularity, uniqueness and very limited production numbers. Even though it wasn't intended to be a limited edition, it became one overnight. No more than 500 of this Astrographic 2000 were produced with black, blue and silver dials in round and square cases. Even so, they were dumped into the market at very low prices. The Astrographic 2000 is made of materials with quality of workmanship in fit, finish and assembly befitting a watch with its original MSRP. The case, signed screw-down crown and signed back are solid stainless steel. The back, which is held on by screws, has a very large Zodiac logo deeply etched into it. Surprising for a cross between a dress and sports watch, it has a 200 meter diver depth rating. The movement inside is the venerated 25 jewel 28,800 bph ETA 2824-2 automatic. Its high beat gives the orbiting red moon seconds "hand" an extremely smooth motion around the very deep lapis blue, fine sunburst texture dial. The case is 38 mm in diameter and 12mm thick. The crystal is heavy, flat sapphire, and the 20mm wide integral band is 3mm thick, made of solid stainless steel links, with a signed butterfly clasp. The Zodiac Astrographic 2000 is a piece of Zodiac's history embodied in one of its most popular and distinctive models, updated with top notch materials and impeccable workmanship. Even though Fossil has quite successfully stabilized and improved Zodiac financially, it's highly unlikely they will ever make a watch like the Astrographic 2000 again. The probability of it is better characterized as nearly zero. Summary:
  • Updated version of the original 1971 Astrographic SST
  • 500 in each style made during 1999 and only offered for sale for 13 months in 2000-2001
  • 38 mm diameter
  • 12 mm thick
  • 20 mm wide X 3mm thick solid stainless steel band
  • 180 grams
  • 200 meter depth rating
  • ETA 2824-2 25 jewel, 28,800 bph auto movement
  • Solid stainless steel case, crown and back
  • Sapphire crystal
  • Signed back, crown, and pushbutton butterfly clasp
  • Unique orbiting satellite hour/minute and red moon seconds hands "mystery dial"
Original MSRP was $1,295 in 2000. "New Old Stock," when it can be found, has a current "street price" of about $500, but they have all but completely disappeared now.
Zodiac's Current Web Site
Note: I do not have any association with Zodiac, Fossil or their dealers, for new or NOS, other than having bought a NOS Zodiac Astrographic 2000 from a dealer in vintage Zodiacs.

Tuesday, August 28, 2007

Mechanical Watches: Adjustment and Regulation

Two definitions:
Precision: repeatability without variation
Accuracy: ability to hit the desired target

All time-keeping devices I've seen or read about operate either on a "pulse" or "oscillator" whether they're electronic, electro-mechanical or completely mechanical. Their ability to measure passage of time ("time-keeping") relies on both ability to repeat the pulsing or oscillation with as little variation as possible, and the (mean or average) frequency of the oscillator being set as closely as possible to the desired frequency. The amount of variation in its repeated oscillations is a measure of its precision. The mean (average) frequency of the oscillator as compared to it's proper value, is its accuracy.

It's not possible to set accuracy to an extremely tight tolerance unless there is extremely high precision. This is a problem encountered by those trying to tweak watches to extreme accuracy (exceeding that of certified chronometers) that have "off the shelf" workhorse mechanical movements. It is an attempt to achieve an accuracy that exceeds the movement's (current) precision, especially when worn daily which varies the movement's orientation and to some extent, its temperature. Gravity and the movement's position relative to it has a measurable effect on mechanical movements, as does motion of the movement when in use. Temperature affects both mechanical and quartz movements.

In horology, a timepiece with high precision is described as being "well adjusted." A very low "drift" (gain or loss over time) compared to a time standard such as that provided by the U.S. Naval Observatory (USNO) or the Nat'l Institute of Science and Technology (NIST; formerly the Nat'l Bureau of Standards, NBS) is characterized as being "well regulated." Before regulating a watch, it must be adjusted for sufficient precision that allows it to be regulated to the desired accuracy. A watch's precision (how well it's adjusted) ultimately limits its accuracy (how well it can be regulated), no matter how much its regulation is "tweaked."

While many things can be done in most mechanical watches to adjust them, how well the movement is designed, especially the balance wheel, escapement, and mainspring can make adjustment easy or very difficult, and it establishes a baseline precision from which adjustment is made (if desired) to improve it. Three major environmental factors affect their adjustment:
  • orientation to gravity,
  • motion (including vibration), and
  • temperature.
The watch's variation will be how these factors affect the specific design, and the adjustment (if performed after assembly) of the balance wheel, its hairspring and the escapement. All three, especially motion and temperature, plus state of wind (how tightly the mainspring is wound) affect isochronism, which is ability to maintain a stable frequency regardless of how many degrees the balance wheel rotates. A pendulum analogy is the pendulum having the same period (how long it takes to make a complete cycle) regardless of how far the pendulum swings.

Gravity and Watch Orientation:
This causes minor differences in escapement operation and the bearing of shafts on pivot points that varies the friction in them. There are six basic positions in which a watch can be tested for the effect of gravity on its beat rate: dial up, dial down, crown up, crown down, crown left, and crown right. Adjusting a watch for precision in all these positions is very time consuming and very expensive. It requires tweaking the exact position of staff and shaft pivots . . . and can require tweaking the balance wheel hairspring (usually done to reduce isochronal error).

Motion:
Motion of the person carrying or wearing the watch, particularly if it rotates the movement, or vibrates it, combined with its orientation to the motion can affect the how many degrees the balance wheel rotates. If there is isochronal error related to balance wheel rotation, the balance wheel period will vary, and timekeeping will vary accordingly.

Temperature:
Changes cause expansion or contraction of all the parts, changing their dimensions, particularly the balance wheel diameter and the hairspring. Materials such as bimetallics and designs that inherently compensate for temperature changes to maintain the same tension on springs, and the rotational inertia of rotating parts help reduce temperature effects. A temperature change and how tightly the mainspring is wound will shift a watch's regulation. How much it shifts is a matter of how much the temperature changes, and how well the design of the balance, hairspring, escapement and mainspring compensate for temperature change, and the mainspring maintaining constant tension (force) as it unwinds from fully wound to fully unwound.

Stringent chronometer standards test timepieces for timekeeping accuracy (its regulation) while inducing conditions that can cause variation at different temperatures and in different orientations called positions (its adjustment). As much hype as the Swiss COSC creates about its chronometer certifications, it is the least stringent of the three major standards that have existed. Furthermore, it's done on the bare watch movement, without any complications, and without its auto-wind rotor (if it's an auto-wind movement). Final assembly of the movement, and assembly into the watch case is done afterward, followed by shipping to the retailer. The U.S. Railroad Standard established at the end of the 19th Century required greater accuracy, and it was performed on the completely assembled watch, just as it would be used. The most stringent was the British Kew Observatory standard established for naval and maritime navigation chronometers. Its complete test required 45 days! If still done (which I doubt), it's now performed by the British NPL (National Physics Laboratory). Kew chronometer testing was also performed on completely assembled chronometers.

Given the materials and modern designs that limit, prevent or compensate for variation of a mechanical movement's regulation, the most important remains positional adjustment. Inside older, higher end watches, it's not uncommon to find the number of positional adjustments made when the watch was manufactured. Typical is either three positions, five positions or "unadjusted" (zero positions; all testing was likely dial up). Rarely is a wrist or pocket watch adjusted for all six positions. The most common position omitted for a wristwatch is crown right (or "12" up). Which is omitted for a pocket watch usually depends on whether it has an open face (no cover over the crystal) or is a "hunter" or "field" style with a hinged metal cover over the crystal.

Most modern Japanese and Swiss movements found in the mid-range to high-range watches are unadjusted workhorse Miyota, Seiko and ETA movements with 17 or more jewels. Their design, particularly the balance, escapement, hairspring and mainspring, have made adjusting movements for this market range unnecessary. Factory regulation can get their accuracy well within about 20 seconds daily gain/loss, the common factory specification. It's almost always much better than that (approx. +/- 10 sec./day). Their variation in daily gain/loss rate (precision) is usually much less than +/- 5 seconds per day.

These watches can quite often be regulated later by a watchmaker experienced with mechanical movements and knows what he's doing, to within 10 seconds gain or loss per day without any adjustment. That's a little over a minute per week, and it assumes the movement in good mechanical working condition (good lubrication, no corrosion, etc.). He'll keep it a few days although he won't spend much bench time working on it. The calendar time is needed to let it run a day so between tweaking its regulation a couple times, and then verify after another day of running that his tweaking hasn't gone too far in either direction. Some of how well he can tweak it depends on the balance regulator and how finely it allows moving it. Some have a screw for fine tuning its regulation; others do not.

Some exceptions in the high-range might be those destined to undergo COSC chronometer certification. COSC is expensive enough to push these exceptions into the upper end of high range pricing. It depends on the watchmaker whether or not the movement is adjusted before it's submitted to COSC for testing. Adjustment is most typically reserved for the luxury and prestige watch movements. It's very time consuming and quite costly compared to regulating a movement. Many of the movements from the most widely recognized of these brands are not only adjusted to three or five positions, they're COSC certified (e.g. Rolex and Omega).

Attempting to achieve +/-4 second regulation or better with any mechanical watch movement, no matter how well designed and adjusted, even the COSC certified prestige and luxury watch movements, is nearly impossible if the watch is worn daily. Such regulation accuracy exceeds that of the British Kew Observatory Standard! In my very humble opinion, achieving better than +/-20 seconds in a 24 hour period, typical of the factory specifications for unadjusted movements in the inexpensive, basic lines of mechanical watches sold for less than $200, with many under $100, is very good, and quite a few are much better than that out of the box. That unadjusted movement mid-range and high-range watches are typically +/- 10 second daily gain/loss out of the box is excellent.

Swatch Group ETA Mechanical Movement Alternatives

Filling Swatch Group's ETA Mechanical Movement Void Sellita, Miyota, Soprod, and Ronda In 2002, Nicolas Hayek, then CEO of the Swatch Gr...